Why a Battery Management System (BMS) is needed?

Why a Battery Management System (BMS) is needed? - Tewaycell

A standard lithium cell is 3.2V. To turn these individual cells into a safe 12/24 or 48V battery requires a Lithium Battery Management System or BMS. A BMS is a circuit board that has a connection to the cells and monitors the overall battery. For safety reasons the BMS needs to ensure that the cells are always operating within known limits and to actively respond if these limits are breached.

Why a Battery Management System (BMS) is needed:

Charging

If lithium cells are overcharged, it will shorten their lifespan or perhaps permanently damage them. So with a LiFePO4 (Lithium Iron Phosphate) battery whose nominal voltage is 3.2 volts, you should never charge them above 3.65 volts and it is best to have something in the system that will shut the charger off when they reach a maximum charge voltage of 3.65 volts. Similarly, with a LiNCM or LiMn204 (Lithium Polymer) battery whose nominal voltage is 3.7 volts, you should never charge them above 4.2 volts and it is best to have something in the system that will shut the charger off when they reach a maximum charge voltage of 4.2 volts.

Discharging

Conversely, a LiFePO4 lithium battery cannot be discharged below 2.4 volts without damage to the cells. So there must be some mechanism in the system which will automatically throttle back and eventually shut the battery pack down in the event of a discharge condition that goes below 2.4 volts. If that mechanism isn’t in the place you risk damaging some of the batteries in your pack. This system is commonly referred to as a Battery Management System or BMS or in the case of some smaller battery packs, like in a bicycle, a PCM. A PCM (Protective Circuit Module), which is often called a PCB (Protective Circuit Board), is a passive system that will operate best at voltages of less than 96 volts and peak currents that never go over 200 Amps.

Balancing

Having a number of batteries all connected up together storing electric energy is somewhat like having a barrel that is made from wooden staves which are of varying length that is storing water. Some batteries will accept a charge better than other batteries in the string. When they reach a predetermined voltage like 3.65 for LiFePO4 batteries then there has to be a way to shunt current from that highest charged battery and prevent it from becoming overcharged while their weaker batteries in the same string catch up. To simplify that I have used the storing water in a wooden barrel analogy and show the longer staves as the good batteries while the shorter staves represent the weaker batteries. This is the third function of a BMS. A good BMS will balance all the batteries so that they reach full charge in about the same time. This might be shown as a barrel that has all of the staves at the same length. Passive BMS systems contain large resister networks which merely redirect the charging current through the resister network and burn up excess power while the balance of weaker cells are getting to their full recharge voltage level. 

Cheap BMS systems do not do this they merely turn the charger off when the first battery nears 3.65 volts. With those systems, the battery pack could still be charged with a greater amount of power but there isn’t any way these cheap systems will allow that to happen. Thus you may lose as much as 20% of the battery packs full potential capacity for the sake of a few dollars saving when purchasing the BMS system. In motor vehicles that can amount to a big loss of range. 

The fourth BMS function concerns protecting and balancing the batteries from over-discharging. If the batteries are somehow not balanced so that all of the staves are equal, which a properly engineered BMS system will do, than as the battery is discharged the weakest battery, represented in my illustration by the shortest stave in the barrel, will reach its full discharge shutoff point ahead of the rest of the pack. A good BMS system will keep all the cells balanced so that the weakest cell voltage with a LiFePO4 battery will not go below 2.4 volts while the other batteries are allowed to drain their energy. Similarly, a good BMS system will also keep all the cells balanced in a Lithium Polymer battery so that the weakest cell voltage will not go below 2.8 volts while the other batteries are allowed to drain their energy. A well-designed BMS will assure that all of the batteries are close to equal in storing and discharging their energy uniformly. The last function of a good BMS system is monitoring and controlling the temperatures within the cells or the total pack. Many lithium chemistries like Lithium Cobalt can spontaneously burst into flames if they are overcharged or discharged. Metal fires are extremely hot and water or even fire fighting foams alone will not extinguish the flames. Of all the lithium chemistries Lithium Iron Phosphate (LiFePO4) is the least volatile and theoretically will not combust. However, extreme heat can damage and shorten the life in all lithium cells. A good BMS system will monitor the temperatures within a pack and either shut the pack down or throttle back the discharge or charging current so that the cells never reach a point of overheating.

RELATED ARTICLES

Leave a comment

Your email address will not be published. Required fields are marked *

Please note, comments must be approved before they are published